PLANEX Bluetooth対応 USBアダプタ BT-02UD2
利用したハードウェア
利用したソフトウェア
- module: hci_usb.o rfcomm.o l2cap.o bluez.o
Bluetoothデバイスを起動する。
# /etc/rc.d/init.d/bluetooth start
Starting Bluetooth subsystem: hcid sdpd rfcomm |
本体 SL-C3000のUSBポートにPocket USBホスト ケーブルのミニB5ピンを挿して
PLANEX Bluetooth対応 USBアダプタ BT-02UD2 を接続して
Pocket USBホスト ケーブルのAタイプ/メスに挿入する。
USB
|- USB OHCI Root Hub
|- RF Controller
Vendor:
Product: RF Controller
Class: RF Controller
ID: 4851/1103
Driver: hci_usb |
Module Size Used by
rfcomm 33632 0 (autoclean)
l2cap 16432 2 (autoclean) [rfcomm]
hci_usb 9088 1
bluez 33216 3 [rfcomm l2cap hci_usb]
pxa_bi 24912 0 (unused)
storage_fd 100336 0 (unused)
usbdcore 35504 0 [pxa_bi storage_fd]
usbdmonitor 5488 0
usb_ohci_pxa27x 21696 0 (unused)
usbcore 63264 1 [hci_usb usb_ohci_pxa27x]
usb-monitor 6496 0
sharp_mmcsd_m 41008 2 |
dmesgに表示されたメッセージは、
メッセージの最後に
hub.c: USB new device connect on bus1, assigned device number 2
usb.c: kmalloc IF c30f4720, numif 2
usb.c: new device strings: Mfr=0, Product=0, SerialNumber=0
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0x4851/0x1103) is not claimed by any active driver.
Length = 18
DescriptorType = 01
USB version = 1.10
Vendor:Product = 4851:1103
MaxPacketSize0 = 64
NumConfigurations = 1
Device version = 11.19
Device Class:SubClass:Protocol = e0:01:01
Unknown class
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 00b1
bNumInterfaces = 02
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = c0
MaxPower = 0mA
...
usb.c: kusbd: /sbin/hotplug add 2
BlueZ Core ver 2.4 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky
BlueZ HCI USB driver ver 2.7 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky
usb.c: registered new driver hci_usb
usb.c: hci_usb driver claimed interface c30f4738
usb.c: hci_usb driver claimed interface c30f4720
BlueZ L2CAP ver 2.3 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky
BlueZ RFCOMM ver 1.1
Copyright (C) 2002 Maxim Krasnyansky
Copyright (C) 2002 Marcel Holtmann |
hciconfig を実行する。
# hciconfig
hci0: Type: USB
BD Address: 00:11:22:33:44:55 ACL MTU: 192:8 SCO MTU: 64:8
UP RUNNING PSCAN ISCAN
RX bytes:99 acl:0 sco:0 events:13 errors:0
TX bytes:296 acl:0 sco:0 commands:12 errors:0 |
hcitool scanを実行する。
# hcitool scan
Scanning ...
00:11:22:33:44:55 XXXXXXXXXX |
USBホスト Top Page に戻る
更新日時:
[an error occurred while processing this directive]
お問い合わせ:
本サイトに対する御意見・質問等はこのページからお願いします。